Planning your installation? Use this page to help you source all the supplies you need to help the install go efficiently and accurately. Below you'll find links for supplies for wood-framed building installs and metal-framed building installs.

*This page contains some affiliate links. If you choose to purchase after clicking one, we may receive a small commission, at no extra cost to you.

For every installation you will at least need:

	BlueTex™ Insulation Pro (2mm): EPE foam product combined with reflective aluminum foil to REFLECT radiant heat and provide basic moisture prevention. Rolls are 62" x 135' 6" long (700 sq ft) each
	BlueTex™ Insulation Pro (2mm): EPE foam product combined with reflective aluminum foil to REFLECT radiant heat and provide basic moisture prevention. Rolls are 50" x 168' long (700 sq ft) each
	BlueTex™ Insulation Supreme (6mm): XPE foam combined with a bright white side for interior aesthetic and a 99% reflective aluminum foil to REFLECT radiant heat and provide MAXIMUM moisture prevention. Rolls are: 50" x 72' long (300 sq ft) each
	BlueTex™ Insulation Supreme (6mm): XPE foam combined with a bright white side for interior aesthetic and a 99% reflective aluminum foil to REFLECT radiant heat and provide MAXIMUM moisture prevention. Rolls are 62' x 59' long (300 sq ft) each
	Matching FOIL tape (optional) - This is usually for new construction where you can tape the outside seam before the metal goes up. Foil Tape rolls are 3" wide by 150' long.
	Matching WHITE tape (optional) - this is useful to clean up the install (covering fasteners, attaching edges, etc.) White Tape available in 3" wide, 4" wide, and 6" wide rolls. Tape rolls are all 180' long.

*Click on an image to shop*

Metal-Framed Installation Supplies

Screw Method (metal-framed buildings)

	Magnetic arm band (great for small jobs too!)
	Metal locking washers & #8 hex head ¾" self-drilling screws. To use the locking washers with the screws, just push the screw through hole before attaching. These can be pre-painted white to match if the white layer is facing inside.

*Click on an image to shop.*

Shish-Kebab Method: Glued/Perforated Pins (metal-framed buildings)

	Perforated pins (these pins have small holes in the base where your adhesive will bond the base of the pin to the metal surface in the building) and locking metal washers to secure the insulation onto the pins. Pin Length Recommendation: 1" to 1.5" long at minimum We have these in limited supply. Call to order: 1-800-595-8772 or click the image on the left to find them on Amazon.
	Boss Multi-Seal 180 (this is an adhesive rated for high temperatures). You should be able to glue 100-200 pins per tube of multi-seal adhesive.
	Another adhesive recommendation from customers. Good for application in colder months. Click the image to buy.
	Styrofoam (or cardboard) for holding pins while you squeeze adhesive onto the perforated base of the pins.

*Click on an image to shop.*

Wood-Framed Installation Supplies

Screw + Washer Method (wood-framed buildings)

Metal locking washers & #8 hex head ¾" self-drilling screws.

To use the locking washers with the screws, just push the screw through hole before attaching. These can be pre-painted white to match if the white layer is facing inside.

*Click on an image to shop.*

Magnetic arm band (great for small jobs too!)

Additional Insulation Installation Supplies

The HDPE furring strip spacers are great for use in NEW construction when you're wrapping the outside of the building to create the air gap between the foil surface of BlueTex™ and the metal skin.

The air gap allows the foil to work as a radiant barrier to reduce heat gain in the summer and heat loss in winter.

Double-Sided tape has a myriad of uses but particular to BlueTex™ installation, this can be used to attach the BlueTex™ to the outside of your frame without using fasteners.

You can also use the double-sided tape to attach the 2mm Pro BlueTex™ to your roll up garage door or residential panel style garage door.